Product Information

Specification

Specifications

Conductors:Bare soft annealed copper, Class B, 7-strand concentric per ASTM B-8.
Insulation: Flame-retardant, radiation-resistant Okozel, a modified ETFE fluoropolymer. Cable meets or exceeds requirements for UL Standards 13 and 2250.
Jacket: Nylon per UL 83, 4 mils nominal thickness.
Conductor Identification: Pigmented black and white in pairs, black, white and red in triads.
Assembly: Pairs or triads assembled with a 1½€�-2 ½€� left-hand lay. Flame-retardant, non-wicking fillers included where required to provide a round cable, polyester tape overall.
Cable Shield: Aluminum-nylon-polyester tape overlapped to provide 100% coverage, and a 7-strand coated copper drain wire, same size as conductor.
Inner Jacket: Black, flame-retardant Okoseal per UL Standard 1569. A rip cord is laid longitudinally under the jacket to facilitate removal.
C-L-X Sheath: A close-fitting, impervious, continuously welded and corrugated, aluminum sheath meeting UL 1569 provides complete protection against moisture,liquids, and gases, has excellent mechanical strength, and provides equipment grounding through the sheath
Outer Jacket: Black, flame-retardant Okoseal per UL Standard 1569.

Applications

Okonite C-L-X Single pair or triad type P-OS instrumentation cables are designed for use on Class 1 Remote-Control Signaling circuits or where a 600V cable is desired, as instrumentation, process control, or computer cable transmitting signals at levels above 100 milli-volts in circuits where shielding against external interference is required, but shielding against interference among groups is not required. For use indoors or outdoors; wet or dry locations; in cable trays; in raceways; supported by a messenger wire; for direct burial; in Classes I, II, and III, Divisions 1 and 2 hazardous locations per NEC Articles 501, 502, 503, 504 and 505; in Zone 2, Class II Div 2, Class III Div 1 and Class III Div 2 per CEC. The overall shield eliminates most of the static interference from the electric field radiated by power cables and other electrical equipment.
The C-L-X sheath provides the physical protection against mechanical damage as required in NEC Section 725-8 as well as complete protection against moisture or gases entering the cable.
For dc service in wet locations, X-Olene insulation is recommended.
These cables also comply with UL requirements for Types CL2 and CL3.

Product Features

• Complete pre-packaged, factory-tested wiring system€”color coded.
• C-L-X enclosure permits installation in cable tray containing light and power cables without a barrier separator.
• Impervious, continuous sheath excludes moisture, gases and liquids.
• C-L-X sheath exceeds equipment grounding conductor requirements of NEC Section 250-122, for Non-HL locations.
• Excellent compression and impact resistance.
• Lower installed system cost than conduit or EMT systems.
• Suitable for low temperature installation to -40°C.

Applicable Standards

• UL listed for cable tray use, direct burial and sunlight resistant.
• Vertical Tray Flame Tests.
  IEEE 383-1974, FT4/IEEE 1202,
  ICEA T-29-520 (210,000 BTU)
• American Bureau of Shipping Type approved as CWCMC Type MC-HL.
• API Standards 14F and 14FZ.
• ASTM B-8.
• OSHA Acceptable
• UL 2225 Type MC-HL
• UL 83
• UL 1309 (CWCMC) Marine Shipboard
• UL 1569
• UL certified as Marine Shipboard in accord with IEEE 1580, Marine Shipboard Cable rated 600/1000 volts.
• NEC Articles 501, 502, 503, 504 and 505 for Classes I, II and III, Divisions 1 and 2 Hazardous Locations.
• NPLF per NEC Code Article 760.
• CSA C22.2 No. 230 Type TC
• CSA C22.2 No. 239 Type ACIC
• cUL Type ACIC-TC complies with CEC Zone 2, Class II Div 2, Class III Div 1 and Class III Div 2 Hazardous Locations.

*Data provided on this page is subject to change based on different manufacturers' variances

** Images are for display purposes only refer to Product Technical Details for accurate information on the product.

In the case the material only comes in a predetermined color or doesn’t come with any color